By Plumbing Guide for Bathtub Installation
By Plumbing Guide for Bathtub Installation
Blog Article
Everyone may have their own unique rationale involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Mounting a bathtub isn't specifically rocket science, however it does require solid plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a new one is also a reasonably tough task. If the old tub is readily easily accessible, the project can move quickly; if you need to open a wall to remove the old tub and position the brand-new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub as well as embeded in the brand-new one. Ensure you have qualified on your own for the task and also are comfortable trying it. Rather than working with a service provider to take control of a halfway-completed project, it is better to take into consideration using one before you start. Possibilities are you might require an expert plumber to make tube connections.
This write-up will assist you mount a new bathtub in your restroom if you have actually currently bought a new bathtub as well as don't require to transform the arrangement of your previous supply of water pipes.
Your tools and material checklist need to make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of removing the existing faucets can be quite problematic as a result of the restricted gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washers are in place between the tap and the sink. Secure the tap in place with the producer given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap adapters. The previous kind needs to be connected to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Tub
Utilizing the two wooden boards under its feet, put the tub in the required placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to ensure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as readjusting the feet on the tub until the level reads level.
To set up faucets, fit the bottom of the outermost adaptable faucet port to the proper supply pipe by making a compression join; after that do the very same for the other faucet.
Activate the water system and also check all joints and new pipework for leakages and also tighten them if required. Fill up the bath tub and also check the overflow electrical outlet and the regular outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's user's manual. Tiling and securing around the bath tub ought to wait up until the bath tub has been made use of at the very least when as this will certainly resolve it into its last setting.
Getting ready for the Setup
First of all, the supporting framework supplied with the bathroom needs to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to stop stress on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a stiff seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, leading to problems with wetness as well as possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealer can split relatively early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily offered on the market. It is advisable to fit the floor tiles making use of water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader about Installing A Bathtub, I was thinking sharing that information was important. Sharing is good. You never know, you may just be doing someone a favor. Thanks for going through it.
Plumbing care available. Report this page